Measuring, Marking and Practice – ITI NIMI Mock TestTest Measuring, Marking and Practice (मापना, चिह्नित करना और अभ्यास करना) – ITI NIMI Mock Test Mechanic Diesel Theory Measuring, Marking and Practice - ITI NIMI Mock Test Mechanic Diesel Theory 1 / 701. Q. Name the part marked as x | X के रूप में चिह्नित भाग को नाम दें? A) Snug | गरम B) Spindle | धुरा C) Guide pin | गाइड पिन D) Rocker arm | हाथ से घुमाना 2 / 702. Q. What is the use of lump hammer? | गांठ हथौड़ा का उपयोग क्या है? A) Strike the metal | धातु पर प्रहार करो B) Punch the metal | पंच धातु C) Spread the metal | धातु फैलाओ D) Light demolition work | हल्का विध्वंस कार्य 3 / 703. Q. What is the name of the spanner? | स्पैनर का नाम क्या है? A) Socket spanner | सॉकेट स्पैनर B) Tubular spanner | ट्यूबलर स्पैनर C) Hook spanner | हुक स्पैनर D) Adjustable spanner | एडजस्टेबल स्पैनर 4 / 704. Q. What is the name of the part marked asx? | X के रूप में चिह्नित भाग का नाम क्या है? A) Anvil | निहाई B) Frame | ढाचा C) Spindle | धुरा D) Thimble | नोक 5 / 705. Q. Calculate the value of 1 vernier scale in the figure. | आकृति में 1 वर्नियर स्केल के मान की गणना करें। A) 0.06 Units B) 0.07 Units C) 0.08 Units D) 0.09 Units 6 / 706. Q. Which vice is used to hold a very small diameter job? | किस वाइस का उपयोग बहुत छोटे व्यास की नौकरी के लिए किया जाता है? A) Pipe vice | पाइप वाइस B) Hand vice | हैण्ड वाइस C) Pin vice | पिन वाइस D) Tool maker's vice | टूल मार्क वाइस 7 / 707. Q. What is the name of calliper? | कैलिपर का नाम क्या है? A) Firm joint caliper | फर्म संयुक्त कैलिपर B) Spring joint caliper | स्प्रिंग ज्वाइंट कैलीपर C) Inside caliper | कैलीपर के अंदर D) Jenny caliper | जेनी कैलिपर 8 / 708. Q. Which instrument is used to check the endplay of crankshaft? | बँक शाफ्ट के एंड-प्ले की जांच के लिए किस उपकरण का उपयोग किया जाता है? A) Dial test indicator | डायल टेस्ट इंडिकेटर B) Telescopic gauge | टेलीस्कोपिक गेज C) Bore dial gauge | बोर डायल गेज D) Slip gauge | स्लिप गेज 9 / 709. Q. Which marking media is poisonous? | कौन सा मार्किंग मीडिया जहरीला है? A) White wash | सफेद धोना B) Prussian blue | हल्का नीला C) Copper sulphate | कॉपर सल्फेट D) Cellulose lacquer | सेल्यूलोज लाह 10 / 7010. Q. What is the name of the part marked as x? | X के रूप में चिह्नित भाग का नाम क्या है? A) Cap | टोपी B) Lock | ताला C) Stock | भण्डार D) Graduated sleeve | स्नातक की उपाधि प्राप्त की 11 / 7011. Q. What is the name of the calliper? | कॉलिपर का नाम क्या है? A) Inside caliper | कैलीपर के अंदर B) Outside caliper | बाहर का खलीफा C) Firm joint caliper | फर्म संयुक्त कैलिपर D) Spring joint outside caliper | कैलिपर के बाहर स्प्रिंग जॉइंट 12 / 7012. Q. What is the name of equipment? | उपकरण का नाम क्या है? A) Surface plate | ऊपरी तल B) Angle plate | कोण प्लेट C) 'V' Block | वी ब्लॉक D) Parallel Block | समानांतर ब्लॉक 13 / 7013. Q. What is the least count of engineer steel rule? | इंजीनियर स्टील नियम की सबसे कम गिनती क्या है? A) 1 mm B) 0.5 mm C) 2 mm D) 3 mm 14 / 7014. Q. What is to be checked with vacuum gauge? | टीके गेज के साथ क्या जाँच की जानी चाहिए? A) Leak in the cooling system | शीतलन प्रणाली में रिसाव B) Leak in the air brake system | एयर ब्रेक सिस्टम में रिसाव C) Leak in the inlet-manifold system | इनलेटमैनिफोल्ड सिस्टम में रिसाव D) Leak in the hydraulic brake system | हाइड्रोलिक ब्रेक सिस्टम में रिसाव 15 / 7015. Q. What is the angle of prick punch? | चुभन पंच का कोण क्या है? A) 60° B) 90° C) 120° D) 180° 16 / 7016. Q. What is the reading of the outside micrometer (0-25 mm)? | आउट साइड माइक्रोमीटर (0-25 मिमी) की रीडिंग क्या है? A) 2.25 B) 2.5 C) 2.75 D) 20.75 17 / 7017. Q. What is the name of the vice? | वाइस का नाम क्या है? A) Pipe vice | पाइप वाइस B) Hand vice | हैण्ड वाइस C) Tool maker vice | टूल निर्माता वाइस D) Bench vice | बेंच वाइस 18 / 7018. Q. What is the use of outside calliper? | बाहरी कॉलिपर का उपयोग क्या है? A) Check the flatness | सपाटता की जाँच करें B) Check the internal dia of the job | जाब के आंतरिक व्यास की जांच करें C) Check the angle | कोण की जाँच करें D) Check the external dia of the job | job के बाहरी व्यास की जांच करें 19 / 7019. Q. What is the purpose of mallets? | Mallets का उद्देश्य क्या है? A) Riveting operation | रिवेटिंग ऑपरेशन B) Strike on soft metal | स्ट्राइक इन सॉफ्ट मेटल C) Strike on hard metal | स्ट्राइक इन हार्ड मेटल D) Spread the metal to all sides | धातु को सभी तरफ फैलाएं 20 / 7020. Q. What is the material used to make Allen keys? | एलन कीज़ बनाने के लिए किस सामग्री का उपयोग किया जाता है? A) Cast iron | कास्ट आयरन B) Aluminium alloy | एल्युमीनियम एलाय C) High speed steel | हाई स्पीड स्टील D) Chrome vanadium steel | क्रोम वैनेडियम स्टील 21 / 7021. Q. Which part actuates the movement of the dial for reading measurement of dial bore gauge? | डायल बोर गेज के मापन के लिए डायल के आंदोलन को कौन सा भाग सक्रिय करता है? A) Stem | तना B) Plunger | सवार C) Fixed anvil | फिक्स्ड एनविल D) Centring shoe | केंद्रित जूता 22 / 7022. Q. What is the name of the spanner? | स्पेनर का नाम क्या है? A) Open spanner | ओपन स्पैनर B) Tubular spanner | ट्यूबलर स्पैनर C) Socket spanner | सॉकेट स्पैनर D) Ring spanner | गोल पाना 23 / 7023. Q. Which part ensures uniform pressure on the measuring faces in the outside micrometer? | कौन सा हिस्सा बाहरी माइक्रोमीटर में मापने वाले चेहरों पर समान दबाव सुनिश्चित करता है? A) Barrel | बैरल B) Spindle | धुरा C) Thimble | नोक D) Ratchet stop | शाफ़्ट स्लोप 24 / 7024. Q. What is the name of the chisel? | छेनी का नाम क्या है? A) Flat chisel | फ्लैट चिजल B) Cross cut chisel | क्रॉस कट चिजल C) Half round nose chisel | हाफ राउंड नोज चिजल D) Diamond point chisel | डायमंड पॉइंट चिसल 25 / 7025. Q. Which marking device used to scribe circle? । किस अंकन उपकरण का उपयोग सर्कल के लिए किया जाता है? A) Jenny caliper | जेनी कैलिपर B) Inside caliper | कैलीपर के अंदर C) Spring divider | स्प्रिंग डिवाइडर D) Out side caliper | साइड कैलिपर 26 / 7026. Q. What is the use of a bench vice? | बेंच उपाध्यक्ष का उपयोग क्या है? A) To hold a work piece | काम का टुकड़ा पकड़ना B) To hold a tool | उपकरण रखने के लिए C) To hold a work table | कार्यतालिका रखने के लिए D) To hold a chuck | एक चक पकड़ करने के लिए 27 / 7027. Q. Which can be measured by feeler gauge? | किसको फीलर गेज द्वारा मापा जा सकता है? A) Radius | त्रिज्या B) Screw pitch | पेंच की पिच C) Surface roughness | सतह खुरदरापन D) Gap between mating parts | संभोग भागों के बीच गैप 28 / 7028. Q. What is the name of the part marked as X in vernier caliper? | वर्नियर कैलिपर में the x के रूप में चिह्नित भाग का नाम क्या है? A) Beam | बीम B) Lock screw | लॉक स्क्रू C) Sliding unit | स्लाइडिंग यूनिट D) Movable jaw | मोवेब्ल जॉव 29 / 7029. Q. Name the part marked as x | X के रूप में चिह्नित भाग को नाम दें? A) Anvil | निहाई B) Clamp | दबाना C) Plunger | सवार D) Stem | तना 30 / 7030. Q. What is the name of the measuring instrument? | मापक यंत्र का नाम क्या है? A) Depth gauge | गहराई गेज B) Bore dial gauge | बोर डायल गेज C) Telescopic gauge | टेलीस्कोपिक गेज D) Vernier gauge | वर्नियर गेज 31 / 7031. Q. Which type of chisel used for squaring material at the corners? | कोनों पर स्क्वरिंग सामग्री के लिए किस प्रकार की छेनी का उपयोग किया जाता है? A) Flat chisel | फ्लैट चिजल B) Half round chisel | हाफ राउंड नोज चिजल C) Cross cut chisel | क्रॉस कट चिजल D) Diamond point chisel | डायमंड पॉइंट चिसल 32 / 7032. Q. What is the reading of vernier caliper with the least count of 0.1 mm? | 0.1 मिमी की सबसे कम गिनती के साथ वर्नियर कैलिपर का पढ़ना क्या है? A) 0.03 mm B) 0.3 mm C) 0.003 mm D) 1.03 mm 33 / 7033. Q. Which is the fixed measuring face of micrometer? | माइक्रोमीटर का निश्चित मापने वाला चेहरा कौन सा है? A) Anvil | निहाई B) Barrel | बैरल C) Spindle | धुरा D) Thimble | नोक 34 / 7034. Q. What is the least count of vernier caliper in metric system? | मैट्रिक सिस्टम में वर्नियर कैलिपर की सबसे कम गिनती क्या है? A) 0.1 mm B) 0.01 mm C) 0.02 mm D) 0.001 mm 35 / 7035. Q. What is the name of the plier? | प्लेयर का नाम क्या है? A) Slip-joint plier | स्लिप-जोइंट प्लेयर B) End cutting plier | एन्ड कटिंग प्लेयर C) Flat nose plier | फ्लैट नोज प्लेयर D) Side cutting plier | साइड कटिंग प्लेयर 36 / 7036. Q. How many equal thimble divisions are made in outside micrometer? | बाहर के माइक्रोमीटर में कितने समान थिमेबल डिवीजन बनाए जाते हैं? A) 30 Divisions B) 40 Divisions C) 50 Divisions D) 60 Divisions 37 / 7037. Q. What is the Purpose of chisel? | छेनी का उद्देश्य क्या है? A) Grinding | ग्राइंडिंग B) Machining | मशीनिंग C) Reaming | रिमिंग D) Chipping | चिपिंग 38 / 7038. Q. Which instrument not used to check inside size of slots? | स्लॉट के आकार के अंदर किस उपकरण का उपयोग किया जाता है? A) Vernier caliper | वर्नियर कैलीपर्स B) Outside micrometer | आउट साइड माइक्रोमीटर C) Inside micrometer | इनसाइड माइक्रोमीटर D) Telescopic gauge | टेलीस्कोपिक गेज 39 / 7039. Q. What is the name of the part marked as X? | X के रूप में चिह्नित भाग का नाम क्या है? A) Anvil | निहाई B) Frame | ढांचा C) Spindle | धुरा D) Thimble | नोक 40 / 7040. Q. What is the value of one thimble division reading in outside micrometer? | बाहर के माइक्रोमीटर में एक थिम्बल डिवीजन रीडिंग का मूल्य क्या हैं? A) 0.05 mm B) 0.01 mm C) 0.02 mm D) 0.03 mm 41 / 7041. Q. Which marking media used to mark in the finished surfaces? | समाप्त सतहों में कौन सा अंकन मीडिया चिह्नित करता था? A) White wash | सफेद धोना B) Prussian blue | हल्का नीला C) Copper Sulphate | कॉपर सल्फेट D) Cellulose lacquer | सेल्यूलोज लाह 42 / 7042. Q. What is the value of one thimble division reading in outside micrometer? | बाहर के माइक्रोमीटर में एक थिम्बल डिवीजन रीडिंग का मूल्य क्या हैं? A) 0.05 mm B) 0.01 mm C) 0.02 mm D) 0.03 mm 43 / 7043. Q. What is the name of the chisel? | छेनी का नाम क्या है? A) Flat chisel | फ्लैट चिजल B) Cross cut chisel | क्रॉस कट चिजल C) Half round nose chisel | हाफ राउंड नोज चिजल D) Diamond point chisel | डायमंड पॉइंट चिसल 44 / 7044. Q. Which instrument used to read the telescopic gauge measurement? | टेलीस्कोपिक गेज माप को पढ़ने के लिए किस उपकरण का उपयोग किया जाता है? A) Depth micrometer | गहराई से माइक्रोमीटर B) Inside micrometer | अंदर माइक्रोमीटर C) Outside micrometer | माइक्रोमीटर के बाहर D) Three point internal micrometer | तीन बिंदु आंतरिक माइक्रोमीटर 45 / 7045. Q. What is the least count of the metric outside micrometer? | माइक्रोमीटर के बाहर मीट्रिक की न्यूनतम संख्या क्या है? A) 0.01 mm B) 0.10 mm C) 0.0001 mm D) 0.00001 mm 46 / 7046. Q. What is the name of the tool? | टूल का नाम क्या है? A) Jack | जैक B) Puller | पुलर C) Wrench | रिंच D) Extractor | एक्सट्रैक्टर 47 / 7047. Q. What is the point angle of centre punch? | केंद्र पंच का बिंदु कोण क्या है? A) 30° B) 45° C) 60° D) 90° 48 / 7048. Q. What is the name of the part marked as X? | X के रूप में चिह्नित भाग का नाम क्या है? A) Spindle | धुरा B) Plunger | सवार C) Fixed Anvil Insert | फिक्स्ड एनविल इंसर्ट D) Centering shoes | जूतों को केंद्रित करना 49 / 7049. Q. What is the name of the hammer part marked asx? | हथौड़ा भाग को x के रूप में चिह्नित किया गया है? A) Cheek | चीक B) Wedge | वेडज C) Face | फेस D) Eye hole | आई होल 50 / 7050. Q. Which part of vernier caliper used to measure internal and external measurement? | आंतरिक और बाहरी माप को मापने के लिए वर्नियर कैलिपर के किस भाग का उपयोग किया जाता है? A) Beam | बीम B) Sliding unit | स्लाइडिंग यूनिट C) Fixed jaw | फिक्स्ड जॉव D) Movable jaw | मोवेब्ल जॉव 51 / 7051. Q. What is the measuring instrument used to measure diameter of a piston pin? | पिस्टन पिन के व्यास को मापने के लिए प्रयोग किया जाने वाला मापक यंत्र क्या है? A) Depth micrometer | डेप्य माइक्रोमीटर B) Inside micrometer | इनसाइड माइक्रोमीटर C) Outside micrometer | आउट साइड माइक्रोमीटर D) 3 point internal micrometer | 3 पॉइंट इंटरनल माइक्रोमीटर 52 / 7052. Q. Which material is used in the outside micrometer anvil? | बाहर के कमाइक्रोमीटर एविल में कौन सी सामग्री का उपयोग किया जाता है? A) Brass | पीतल B) Bronze | पीतल C) Carbon | कार्बन D) Carbide | करबैड 53 / 7053. Q. Which instrument is used to check the right angle? | सही कोण की जांच के लिए किस उपकरण का उपयोग किया जाता है? A) Steel rule | स्टील का नियम B) Try square | वर्ग का प्रयास करें C) Firm joint caliper | फर्म संयुक्त कैलिपर D) Spring Joint caliper | स्प्रिंग ज्वाइंट कैलीपर 54 / 7054. Q. What is the name of the screw driver? | स्क्रू ड्राइवर का नाम क्या है? A) Recess screw driver | स्क्रू ड्रायवर B) Ratchet screw driver | शाफ़्ट स्क्रू ड्राइवर C) Stumpy screwdriver | दमदार स्क्रू ड्राइवर D) Offset screw driver | आफसेट स्क्रू ड्राइवर 55 / 7055. Q. Which screwdriver is used in the space limitation? | स्पेस लिमिट में किस स्क्रू ड्राइवर का उपयोग किया जाता है? A) Cross-recess screw driver | क्रॉस-स्क्रू ड्रायवर B) Ratchet screw driver | रेचेट स्क्रू ड्राइवर C) Stumpy screw driver | स्टंपी स्क्रू ड्राइवर D) Offset screw driver | ऑफसेट स्क्रू ड्राइवर 56 / 7056. Q. Which condition the tyre pressure not to be checked? | टायर की जाँच किस स्थिति में नहीं की जानी चाहिए? A) Tyre is cold | टायर ठंडा है B) Tyre is carrying load | टायर लोड कर रहा है C) Before start of journey | यात्रा शुरू करने से पहले D) Tyre is hot after long run | लंबे समय के बाद टायर गर्म है 57 / 7057. Q. Which instrument is used to measure the diameter of camshaft journals? | केम शाफ्ट पत्रिकाओं के व्यास को मापने के लिए किस उपकरण का उपयोग किया जाता है? A) Depth micrometer | गहराई से माइक्रोमीटर B) Three-point internal micrometer | तीन-बिंद आंतरिक माइक्रोमीटर C) Inside micrometer | अंदर माइक्रोमीटर D) Outside micrometer | माइक्रोमीटर के बाहर 58 / 7058. Q. What is the name of the gauge? | गेज का नाम क्या है? A) Feeler gauge | फीलर गेज B) Snap gauge | स्नैप गेज C) Telescopic gauge | टेलीस्कोपिक गेज D) Plug gauge | प्लग प्रमापक 59 / 7059. Q. Which marking media is used on the rough surfaces? | खुरदरी सतहों पर किस मार्किंग मीडिया का उपयोग किया जाता है? A) White wash | सफेद धोना B) Prussian blue | हल्का नीला C) Copper Sulphate | कॉपर सल्फेट D) Cellulose lacquer | सेल्यूलोज लाह 60 / 7060. Q. What is the reading of vernier caliper with the least count of 0.1 mm? | 0.1 मिमी की सबसे कम गिनती के साथ वर्नियर कैलिपर का पढ़ना क्या है? A) 44.8 mm B) 44.4 mm C) 44.6 mm D) 45.2 mm 61 / 7061. Q. What is the name of the part marked as X? | The x के रूप में चिह्नित भाग का नाम क्या है? A) Anvil | निहाई B) Stem | तना C) Plunger | सवार D) Pointer | सूचक 62 / 7062. Q. Which chisel is used to remove metal from large flat surface? | बड़ी सपाट सतह से धातु निकालने के लिए किस छेनी का उपयोग किया जाता है? A) Flat chisel | फ्लैट चिजल B) Cross cut chisel | क्रॉस कट चिजल C) Half round nose chisel | हाफ राउंड नोज चिजल D) Diamond point chisel | डायमंड पॉइंट चिसल 63 / 7063. Q. What is the name of the device? | डिवाइस का नाम क्या है? A) Pipe vice | पाइप वाइस B) Hand vice | हैण्ड वाइस C) Pin vice | पिन वाइस D) Bench vice | बेंच वाइस 64 / 7064. Q. Name the part marked X in vernier calliper. | Vernier calliper में X वाले भाग को नाम दें? A) 54 B) 54.2 C) 54.4 D) 55.4 65 / 7065. Q. What is the working media of pneumatic tool? | वायवीय उपकरण का कार्य करने वाला मीडिया क्या है? A) Oil | तेल B) Air | वायु C) Water | पानी D) Kerosene | मिटटी तेल 66 / 7066. Q. What is the name of part marked as x? | X के रूप में चिह्नित भाग का नाम क्या है? A) Face | फेस B) Pein | पिन C) Cheek | चीक D) Eye hole | आई होल 67 / 7067. Q. What is the name of the chisel? | छेनी का नाम क्या है? A) Flat chisel | फ्लैट चिजल B) Cross cut chisel | क्रॉस कट चिजल C) Half round nose chisel | हाफ राउंड नोज चिजल D) Diamond point chisel | डायमंड पॉइंट चिसल 68 / 7068. Q. What is the name of the part marked as X? | The x के रूप में चिह्नित भाग का नाम क्या है? A) Spindle | धुरा B) Plunger | सवार C) Centring shoes | जूतों को केंद्रित करना D) Fixed anvil insert | फिक्स्ड एनविल इन्सर्ट 69 / 7069. Q. What is the basic unit of length as per SI unit? | SI इकाई के अनुसार लंबाई की मूल इकाई क्या है? A) Mm B) Cm C) Meter D) km 70 / 7070. Q. What is the purpose of the eye hole in an hammer? | एक हथौड़ा में आई होल का उद्देश्य क्या है? A) Strike the job | जाब से निकाल दिया B) Fix the handle | हैंडल ठीक करें C) Reduce the weight | वजन कम करें D) Stamp the details | विवरण पर मुहर लगाएं Your score is Facebook Restart