Cutting and Bending of Pipe – ITI NIMI Mock Test Plumber TheoryTest Cutting and Bending of Pipe (पाइप को काटना और मोड़ना) – ITI NIMI Mock Test Plumber Theory Cutting and Bending of Pipe - ITI NIMI Mock Test Plumber Theory 1 / 301. Q. Which one gives larger flame? | कौन सी बड़ी लौ देती है? A) Propane torch | प्रोपेन टोर्च B) Acetylene torch | एसिटिलीन टोर्च C) Kerosene blow lamp | केरोसिन ब्लो लैंप D) Oxy-acetylene torch | ऑक्सी-एसिटिलीन टॉर्च 2 / 302. Q. What is the name of part marked as 'X' in the die stock? | डाई स्टॉक में 'X' के रूप में चिह्नित भाग का नाम क्या है? A) Pipe guide lever | पाइप गाइड लीवर B) Die setting lever | डाई सेटिंग लीवर C) Adjustment lever | समायोजन लीवर D) Top piece tightening lever | टॉप पीस टिघटॅनिंग लीवर 3 / 303. Q. What is the name of part marked as 'X' in adjustable screw plate die? | समायोज्य पेंच प्लेट डाई में 'x' के रूप में चिह्नित भाग का नाम क्या है? A) Coller | कॉलर B) Split pieces | स्प्लिट टुकड़े C) Guide plates | गाइड प्लेट D) Leading sides | लीडिंग साइड्स 4 / 304. Q. What is the cause of flare defect? | फ्ले दोष का कारण क्या है? A) Flare is too large | फलरे बहुत बड़ा है B) Flare is uneven | फलरे असमान है C) Flare too small | बहुत छोटा चमक D) Flare has burrs on edge | फलरे किनारे पर burrs है 5 / 305. Q. What is the size of AC pipes available? | एसी पाइप किस आकार में उपलब्ध है? A) 5 cm to 100 cm diameter | 100 सेमी व्यास के 5 सेमी B) 5 cm to 120 cm diameter | 120 सेमी व्यास के 5 सेमी C) 5 cm to 130 cm diameter | 130 सेमी व्यास के 5 सेमी D) 5 cm to 140 cm diameter | 140 सेमी व्यास के 5 सेमी 6 / 306. Q. What type of test to be conducted on S.W. pipe? | S.W पाइप पर किस प्रकार का परीक्षण किया जाना है? A) Flow test | प्रवाह परीक्षण B) Pressure test | दाब परीक्षण C) Vacuum test | वैक्यूम परीक्षण D) Hydraulic test | हाइड्रोलिक परीक्षण 7 / 307. Q. What is the name of part marked as 'x' in a portable hand operated pipe bender? | पोर्टेबल हाथ से संचालित पाइप बेंडर में 'x' के रूप में चिह्नित भाग का नाम क्या है? A) Inside former | इनसाइड फॉर्मर B) Pipe stop lever | पाइप स्टॉप लीवर C) Pipe bend wheel | पाइप बेंड व्हील D) Stop lever | स्टॉप लीवर 8 / 308. Q. What is the working pressure usually made on joints for pressure test? | आमतौर पर दबाव परीक्षण के लिए जोड़ों पर क्या वर्किंग प्रेशर होता है? A) 5 kg/cm2 B) 6 kg/cm2 C) 8 kg/cm2 D) 10 kg/cm2 9 / 309. Q. What is the percentage of silver content in copper to copper brazing rod? | तांबे में कॉपर ब्रेजिंग रॉड में चांदी की सामग्री का प्रतिशत क्या है? A) 15 to 25% | 15 से 25% B) 25 to 35 % | 25 से 35% C) 35 to 45 % | 35 में 45% D) 40 to 50 % | 40 से 50% 10 / 3010. Q. What is the reason for drop in gauge pressure during pressure testing of flare joint? | फ्लेयर जॉइंट के प्रेशर टेस्टिंग के दौरान गेज प्रेशर में गिरावट का कारण क्या है? A) Leak | रिसाव B) Buckle | बकसुआ C) Dent | डेंट D) Bent | बेंट 11 / 3011. Q. what is the largest diameter of pipe that can be held in chain pipe vice? | पाइप का सबसे बड़ा व्यास कौन सा है जिसे चेन पाइप वाइस में रखा जा सकता है? A) 125 mm B) 150 mm C) 175 mm D) 200 mm 12 / 3012. Q. Which tool is used to clean and sharpen the jaw of pipe wrench? | पाइप रिंच के जबड़े को साफ करने और तेज करने के लिए किस उपकरण का उपयोग किया जाता है? A) Flat file | सपाट फ़ाइल B) Rasp file | रास्प फाइल C) Triangular file | त्रिकोणीय फ़ाइल D) Half round file | हाफ राउंड फाइल 13 / 3013.Q. What is the minimum radius required for tubing bend? | ट्यूबिंग मोड़ के लिए न्यूनतम त्रिज्या क्या है? A) 2 times the diameter | 2 बार व्यास B) 3 times the diameter | 3 बार व्यास C) 4 times the diameter | 4 बार व्यास D) 5 times the diameter | 5 बार व्यास 14 / 3014. Q. What is the name of flared fitting? | फ्लेयर्ड फिटिंग का नाम क्या है? A) Flared tee fitting | फ्लारेद टी फिटिंग B) Cross | क्रॉस C) Elbow | एल्बो D) Flared union coupling | फ्लारेद यूनियन कपलिंग 15 / 3015. Q. What is the name of tool? | टूल का नाम क्या है? A) Cutting wheel | काटने का पहिया B) Roller wheel | रोलर पहिया C) Chipped wheel | चिप्पड़ पहिया D) Link wheel | लिंक पहिया 16 / 3016. Q. How to calculate the projection of 3/8 inch from top of the swagging block? | स्वैगिंग ब्लॉक के ऊपर से 3/8 के प्रक्षेपण की गणना कैसे करें? A) Outside diameter of pipe + 1/8 inch | पाइप+ 1/8 इंच का बाहरी व्यास B) Inside diameter of pipe + 1/8 inch | पाइप+ 1/8 इंच के व्यास के अंदर C) Steel punch outer diameter + 1/8 inch | इस्पात पंच बाहरी व्यास + 1/8 इंच D) Steel punch inner diameter + 1/8 inch | इस्पात पंच भीतरी व्यास + 1/8 इंच 17 / 3017. Q. Which flux is used for soldering refrigeration fittings? | रेफ्रिजरेशन फिटिंग के लिए किस फ्लक्स का उपयोग किया जाता है? A) Fallow | फॉलो B) Phosphoric | फॉस्फोरिक C) Hydrochloric acid | हाइड्रोक्लोरिक एसिड D) Alcohol and resin | शराब और राल 18 / 3018. Q. What is the name of symbol as per I.S? | I.S के अनुसार प्रतीक का नाम क्या है? A) Stop valve | स्टॉप वाल्व B) Safety valve | सेफ्टी वाल्व C) Mixing valve | मिक्सिंग वाल्व D) Pump | पंप 19 / 3019. Q. What is the name of part marked as 'x' in hydraulic bending machine? | हाइड्रोलिक बेन्डिंग मशीन में 'X' के रूप में चिह्नित भाग का नाम क्या है? A) Back former | वापस पूर्व B) Inner former | इनर पूर्व C) Hydraulic ram | हाइड्रोलिक रैम D) Base plate | बेस प्लेट 20 / 3020. Q. What is the name of part marked as 'X'? | 'x' के रूप में चिह्नित भाग का नाम क्या है? A) Yoke | योके B) Fixed jaw | फिक्स्ड जॉव C) Holding part | होल्डिंग पार्ट D) Movable jaw | मूवेबल जॉव 21 / 3021. Q. What is the Indian Standard specification of sand cast Cl pipes used for soil pipes? | मिट्टी के पाइपों के लिए उपयोग किए जाने वाले रेत सीआई पाइपों का भारतीय मानक विनिर्देश क्या है? A) IS 1536 B) IS 1538 C) IS 1729 D) IS 3989 22 / 3022. Q. What is swaging? | स्वगिंग क्या है? A) Same diameter pipe joined with fittings | एक ही व्यास पाइप फिटिंग के साथ शामिल हो गए B) Same diameter pipe joined without fittings |एक ही व्यास पाइप फिटिंग के बिना में शामिल हो गए C) Different diameter pipe joined with fittings | विभिन्न व्यास पाइप फिटिंग के साथ शामिल हो गए D) Different diameter pipe joined without _fittings | विभिन्न व्यास पाइप फिटिंग के बिना में शामिल हो गए 23 / 3023. Q. What is the use of sawing fixture? | सइंग फिक्सचर का उपयोग क्या है? A) To hold the job | जॉब पकड़ करने के लिए B) To cut the job | जॉब में कटौती के लिए C) To more the job | अधिक काम करने के लिए D) To guide the tool | उपकरण मार्गदर्शन करने के 24 / 3024. Q. Which one is used to wash out the small particles of dirt in chain pipe cutter? | चेन पाइप कटर में गंदगी के छोटे कणों को धोने के लिए किसका उपयोग किया जाता है? A) Light oil | हल्का तेल B) Petrol | पेट्रोल C) Kerosene | मिटटी तेल D) Turpentine | तारपीन 25 / 3025. Q. What is the name of pipe fitting? | पाइप फिटिंग का नाम क्या है? A) Plug or cap | प्लग और कैप B) Joint/socket | जॉइंट / सॉकेट C) Union unscrewed | यूनियन उनसकरेवेद D) Reducer, concentric | रेडसर , कन्सेन्ट्रिक 26 / 3026. Q. What is the name of part marked as 'x' in hydraulic bending machine? | हाइड्रोलिक बेन्डिंग मशीन में 'X' के रूप में चिह्नित भाग का नाम क्या है? A) Back former | बैक फॉर्मर B) Inner former | इनर फॉर्मर C) Hydraulic ram | हाइड्रोलिक रैम D) Base plate | बेस प्लेट 27 / 3027. Q. What is the name of symbol as per I.S? | I.S के अनुसार प्रतीक का नाम क्या है? A) Hose tack | होसे तक B) Plain kitchen sink | पलाइन किचन सिंक C) Double unit sink | डबल यूनिट सिंक D) Stair | स्तर 28 / 3028. Q. What is the name of die stock? | डाई स्टॉक का नाम क्या है? A) Quick cut die stock | क्विक कट डाई स्टॉक B) Button pattern stock | बटन पैटर्न स्टॉक C) Ratchet type die stock | रैचेट टाइप डाई स्टॉक D) Adjusting screw die stock | अडजस्टिंग स्क्रू डाई स्टॉक 29 / 3029. Q. What is the type of swaging tool for copper tubing? | कॉपर टयूबिंग के लिए स्वेजिंग टूल किस प्रकार का है? A) Punch type | पंच प्रकार B) Lever type | लीवर प्रकार C) Expanded type | विस्तारित प्रकार D) Mandrel type | खराद का धुरा प्रकार 30 / 3030. Q. What is the name of part marked as 'X'? | 'X' के रूप में चिह्नित भाग का नाम क्या है? A) Block | ब्लॉक B) Flaring bar | फ्लॉरिंग बार C) Adaptor | अडाप्टर D) Flaring | फ्लॉरिंग Your score is Facebook Restart