Basic Fitting Operation – ITI NIMI Mock Test Plumber TheoryTest Basic Fitting Operation ((बुनियादी फिटिंग ऑपरेशन)) – ITI NIMI Mock Test Plumber Theory Basic Fitting Operation - ITI NIMI Mock Test Plumber Theory 1 / 461. Q. What is the name of part marked as 'x'? | 'x' के रूप में चिह्नित भाग का नाम क्या है? A) Fixed jaw | फिक्स्ड जा B) Twist drill | ट्विस्ट ड्रिल C) Movable Jaw | मूवेबल जा D) Parallel blocks | पैरेलल ब्लॉक्स 2 / 462. Q. What is the name of chisel? | छेनी का नाम क्या है? A) Flat chisel | फ्लैट छेनी B) Web chisel | वेब छेनी C) Cross cut chisel | क्रॉस कट चिसेल D) Half round nose chisel | हाफ राउंड नोज चिसेल 3 / 463. Q. What is the point angle of centre punch? | केंद्र पंच का बिंदु कोण क्या है? A) 30° B) 45° C) 60° D) 90° 4 / 464. Q. What is the name of caliper? | कैलीपर का नाम क्या है? A) Outside caliper | आउटसाइड कैलिपर B) Odd leg caliper | ओड लैग कैलिपर C) Inside caliper | इनसाइड कैलिपर D) Divider | डिवाइडर 5 / 465. Q. Which material is used to apply as coating on cast iron pipes? | कास्ट आयरन पाइपों पर कोटिंगके रूप में किस सामग्री का उपयोग किया जाता है? A) Molten lead | पिघला लेड B) Bituminous solution | बिटुमिनस घोल C) Molten rubber | पिघला हुआ रबर D) Molten iron | पिघला हुआ लोहा 6 / 466. Q. Which type of fitting is used for easy to dismantle and repair? | किस प्रकार की फिटिंग का प्रयोग आसानी से विघटित और मरम्मत करने के लिए किया जाता है? A) Nipple | प्लग B) Coupling | कपलिंग C) Union | यूनियन D) Reduce | रेदूसर 7 / 467. Q. What is the type of elbow? | एल्बो का प्रकार क्या है? A) 15° elbow | 15° एल्बो B) 45° elbow | 45° एल्बो C) 60° elbow | 60° एल्बो D) 90° elbow | 90° एल्बो 8 / 468. Q. What is the angle of prick punch used for punching witness marks? | विटनेस पंच को छिद्र करने के लिए प्रिक पंच का कोण क्या है? A) 90° B) 80° C) 70° D) 60° 9 / 469. Q. What is the defect of slow and continuous degradation of metallic surface by chemical reaction? | रासायनिक अभिक्रिया द्वारा धात्विक सतह के धीमे और निरंतर क्षरण का दोष क्या है? A) Corrosion | जंग B) Erosion | कटाव C) Lamination | परतबंदी D) Contraction | संकुचन 10 / 4610. Q. What is the name of rivet? | कीलक का नाम क्या है? A) Pan-head rivet | पैन हेड रिवेट B) Flat-head rivet | फ्लैट हेड रिवेट C) Snap-head rivet | स्नेप हेड रिवेट D) Mushroom head rivet | मशरुम हेड रिवेट 11 / 4611. Q. What is the name of die stock? | डाई स्टॉक का नाम क्या है? A) Screw die stock | स्क्रू डाई स्टॉक B) Quick cut die stock | क्विक कट डाई स्टॉक C) Button pattern stock | बटन पैटर्न स्टॉक D) Ratchet type die stock | रैचेट टाइप डाई स्टॉक 12 / 4612. Q. What is the name of chisel? | छेनी का नाम क्या है? A) Flat chisel | फ्लैट छेनी B) Web chisel | वेब छेनी C) Cross cut chisel | क्रॉस कट चिसेल D) Diamond point chisel | डायमंड पॉइंट चिसेल 13 / 4613. Q. What is the use of odd leg caliper? | ओड लैग कैलिपर का उपयोग क्या है? A) For scribing arcs and circles | वृत्त और वृत्त-चाप को चिन्हित करने के लिए B) For marking lines parallel to inside and outside edges | अंदर और बाहरी किनारों के समानांतर रेखाओं को चिह्नित करने के लिए C) For measuring the internal dimensions | आंतरिक आयाम को मापने के लिए D) For measuring the external dimensions | बाहरी आयाम को मापने के लिए 14 / 4614. Q. Why the A.C pipe should be laid with precautions? | ए.सी. पाइप को सावधानियों के साथ क्यों रखा जाना चाहिए? A) More shock resistance | अधिक झटका प्रतिरोध B) Less shock resistance | कम झटका प्रतिरोध C) High shock resistance | उच्च झटका प्रतिरोध D) Medium shock resistance | मध्यम झटका प्रतिरोध 15 / 4615. Q. Which one is an indirect measuring instrument? | अप्रत्यक्ष मापने वाला यंत्र कौन सा है? A) Steel rule | स्टील रूल B) Jenny caliper | जेंनी कैलिपर C) Outside caliper | आउटसाइड कैलिपर D) Bevel protector | बेवल प्रोटेक्टर 16 / 4616. Q. Which nuts are used to protect thread at the bolt end from damages? | कौन से नट का उपयोग बोल्ट छोर पर थ्रेडस को क्षतिग्रस्त होने से बचाने के लिए किया जाता है? A) Wing nut | विंग नट B) Round nut | राउंड नट C) Slotted nut | स्लॉटेड नट D) Domed cap nut | डॉमेड़ कैप नट 17 / 4617. Q. What is the formula used to calculate blank size of round rod before cutting external thread? | बाहरी चूड़ी को काटने से पहले गोल छड़ के खाली आकार की गणना करने के लिए किस सूत्र का उपयोग किया जाता है? A) Blank size=Thread size -0.1% pitch of the thread | रिक्त आकार = चूड़ी का आकार -0.1% चूड़ी की पिच B) Blank size=Thread size +0.1% pitch of the thread | रिक्त आकार =चूड़ी का आकार +चूड़ी की 0.1% पिच C) Blank size=Thread size -0.01% pitch of the thread | रिक्त आकार =चूड़ी का आकार -0.01%चूड़ी की पिच D) Blank size=Thread size +0.01% pitch of the thread | रिक्त आकार =चूड़ी का आकार +चूड़ी की 0.01% पिच 18 / 4618. Q. What is the name of part marked as 'x'? | 'X' के रूप में चिह्नित भाग का नाम क्या है? A) Chuck key | चक की B) Drill chuck | ड्रिल चक C) Chuck holder | चक होल्डर D) Machine spindle | मशीन स्पिंडल 19 / 4619. Q. What is the inclination angle of chisel to cut mild steel? | माइल्ड स्टील को काटने के लिए छेनी का इंक्लाइनेशन कोण क्या है? A) 22° B) 32° C) 34.5° D) 39.5° 20 / 4620. Q. What is the name of punch? | पंच का नाम क्या है? A) Centre punch | केंद्र पंच B) Prick punch | प्रिक पंच C) Number punch | संख्या पंच D) Letter punch | लैटर पंच 21 / 4621. Q. What is the formula to calculate tap drill size? | टैप ड्रिल के आकार की गणना करने के लिए सूत्र क्या है? A) Minor dia = major dia + (2 x depth) | माइनर व्यास = प्रमुख व्यास + (2 x गहराई) B) Minor dia = major dia - (2 x depth) | माइनर व्यास = प्रमुख व्यास - (2 x गहराई) C) Minor dia = major dia + (2 + depth) | माइनर व्यास = प्रमुख व्यास + (2 + गहराई) D) Minor dia = major dia + (2 - depth) | माइनर व्यास = प्रमुख व्यास + (2 - गहराई) 22 / 4622. Q. What type of drill is fixed in the drilling machine? | ड्रिलिंग मशीन में किस प्रकार की ड्रिल फिक्स की गई है? A) Taper shank twist drill | टेपर गैंक ट्विस्ट ड्रिल B) Straight shank twist drill | स्ट्रैट शैंक ट्विस्ट ड्रिल C) Flat drill | फ्लैट ड्रिल D) Square taper shank twist drill | स्क्वायर टेपर शैंक ट्विस्ट ड्रिल 23 / 4623. Q. What is the name of punch? | पंच का नाम क्या है? A) Centre punch | केंद्र पंच B) Prick punch | प्रिक पंच C) Number punch | संख्या पंच D) Letter punch | लैटर पंच 24 / 4624. Q. What is the formation deposited on pipes due to hardness of water? | पानी की कठोरता के कारण पाइपों पर जमा होने वाला फार्मेशन क्या है? A) Scaling | स्केलिंग B) Rusting | रस्टिंग C) Pitting | पिट्टिंग D) Erosion | कटाव 25 / 4625. Q. What is the name of riveted joint? | रिवेटेड जॉइंट का नाम क्या है? A) Single strap butt joint | सिंगल स्ट्राप बट जॉइंट B) Double strap butt joint | डबल स्ट्राप बट जॉइंट C) Single riveted lap joint | सिंगल रिवेटेड लैप जॉइंट D) Double riveted lap joint | डबल रिवेटेड लैप जॉइंट 26 / 4626. Q. What is the name of part marked as 'X'? | 'x' के रूप में चिह्नित भाग का नाम क्या है? A) Peg | पैग B) Spring | स्प्रिंग C) Washer | वॉशर D) Fulcrum | फुलकुम 27 / 4627. Q. What is the weight of hammer used for marking purpose? | अंकन उद्देश्य के लिए उपयोग किए जाने वाले हथौड़े का वजन कितना है? A) 125 gms B) 200 gms C) 250 gms D) 300 gms 28 / 4628. Q. What is the localised formation as cavities or pores on stainless steel due to salty water condition? | नमकीन पानी की स्थिति के कारण स्टेनलेस स्टील पर कैविटीज़ या छिद्रों का लोकलाइज़्ड फार्मेशन क्या है? A) Scaling | स्केलिंग B) Rusting | रस्टिंग C) Pitting | पिस्टिंग D) Ersion | कटाव 29 / 4629.Q. What is the formation on iron and steel caused by moisture and oxidation in atmospheric condition? | वायुमंडलीय स्थिति में नमी और ऑक्सीकरण के कारण लोहे और स्टील पर क्या निर्मित होता है? A) Scaling | स्केलिंग B) Rusting | रस्टिंग C) Pitting | पीटिंग D) Erosion | कटाव 30 / 4630. Q. What is the advantage of cast iron pipes? | कास्ट आयरन के पाइपों का क्या फायदा है? A) Less corrosion | कम जंग B) Rarely available | कम उपलब्धता C) Costly | महंगा D) Crack easily | आसानी से क्रैक होना 31 / 4631. Q. What is the name of process? | प्रक्रिया का नाम क्या है? A) Reaming | रीमिंग B) Drilling | ड्रिलिंग C) Tapping | दोहन D) Counter sinking | काउंटर डूब 32 / 4632. Q. What is used to close the pipe line that has an external thread? | बाहरी चूड़ी वाले पाइप लाइन को बंद करने के लिए क्या उपयोग किया जाता है? A) Plug | प्लग B) Cap | कैप C) Coupling | कपलिंग D) Reducer | रेदूसर 33 / 4633. Q. What is the length of pipe projection required from the vice while threading Gl pipes? | जी आई पाइपों को थ्रेडिंग करते समय वाईस से पाइप प्रक्षेपण की लम्बाई क्या है? A) 100-125 mm B) 125-150 mm C) 150-200 mm D) 150-250 mm 34 / 4634. Q. Which material is used to manufacture punch? | पंच निर्माण के लिए किस सामग्री का उपयोग किया जाता है? A) Low carbon steel | कार्बन की कम मात्रा वाला इस्पात B) High carbon steel | उच्च कार्बन इस्पात C) Medium carbon steel | मध्यम कार्बन स्टील D) Mild steel | नरम इस्पात 35 / 4635. Q. What is the name of nut? | नट का नाम क्या है? A) Sawn nut | सौन नट B) Castle nut | कैसल नट C) Slotted nut | स्लॉटेड नट D) Grooved nut | ग्रूव्ड नट 36 / 4636. Q. what is the type of hammer? | हथौड़े का प्रकार का है? A) Set hammer | सेट हैमर B) Plain hammer | प्लेन हैमर C) Cross hammer | क्रॉस हैमर D) Straight pein hammer | स्ट्रैट पीन हैमर 37 / 4637. Q. Which punch is used to locate the centre of drill point? | ड्रिल पॉइंट के केंद्र का पता लगाने के लिए किस पंच का उपयोग किया जाता है? A) Prick punch | प्रिक पंच B) Centre punch | सेंटर पंच C) Pin punch | पिन पंच D) Hollow punch | होलो पंच 38 / 4638. Q. Which precaution is to be observed while cutting threads in G.I pipe? | G.I पाइप में चूड़ी काटते समय कौन सी सावधानी बरती जानी चाहिए? A) Clean the thread with a wire brush | चूड़ी को एक वायर ब्रश से साफ़ करें B) Apply a soluble oil | घुलनशील तेल लगाएं C) To turn the die stock anti clock wise to break the chips | चिप्स को तोड़ने के लिए डाई स्टॉक को एंटी क्लॉक वाइज मोड़ना D) Apply little pressure to the die stock | डाई स्टॉक पर थोड़ा दबाव डालें 39 / 4639. Q. What is the defect on metal plate with discontinuity or flat and thin subsurface separation on its thickness? | इसकी मोटाई पर समतलता या सपाट और पतले उपसतह अलगाव के साथ, धातु की प्लेट पर क्या दोष है? A) Scaling | स्केलिंग B) Rusting | रस्टिंग C) Erosion | कटाव D) Lamination | परतबंदी 40 / 4640. Q. What is the name of nut? | नट का नाम क्या है? A) Cap nut | कैप नट B) Square nut | स्क्वायर नट C) Hexagonal nut | हेक्सागोनल नट D) Self-locking nut | सेल्फ-लॉकिंग नट 41 / 4641. Q. What material is used to manufacture AC pipes? | एसी पाइप बनाने के लिए किस सामग्री का उपयोग किया जाता है? A) Asbestos fibre, clay, lime | अभ्रक फाइबर, मिट्टी, चूना B) Asbestos fibre, Portlan cement and silica | अभ्रक फाइबर, पोर्टलान सीमेंट और सिलिका C) Asbestos fibre, lime and cement | अभ्रक फाइबर, चूना और सीमेंट D) Asbestos fibre, silica and lime | अभ्रक फाइबर, सिलिका और चूना 42 / 4642. Q. Which material is used to join C.I. pipes? || C.I पाइपों को जोड़ने के लिए किस सामग्री का उपयोग किया जाता है। पाइप? A) Pig lead | पिग लेड B) Molten rubber | पिघला हुआ रबर C) Brass | पीतल D) Zinc | जस्ता 43 / 4643. Q. What is the name of machine? | मशीन का नाम क्या है? A) Pedestal drilling machine | पेडस्टल ड्रिलिंग मशीन B) Bench drilling machine | खंडपीठ ड्रिलिंग मशीन C) Bench grinder | बेंच ग्राइंडर D) Pedestak grinder | Pedestak ग्राइंडर 44 / 4644. Q. What is the use of prick punch 30°? | प्रिक पंच 30 ° का उपयोग क्या है? A) To locate the divider point and scribe circles | विभक्त बिंदु और स्क्राइब सर्कल्स का पता लगाने के लिए B) To punch witness marks | विटनेस मार्क्स पंच करने के लिए C) To punch centre marks | केंद्र के निशान पंच करने के लिए D) To align the drilled holes | ड्रिल किए गए छेदों को संरेखित करने के लिए 45 / 4645. Q. What is the application of inside caliper? | अंदर कैलिपर के आवेदन क्या है? A) To measure external measurement | बाहरी माप को मापने के लिए B) To transfer measurement from steel rule | इस्पात शासन से माप स्थानांतरित करने के लिए C) To measure internal measurement | आंतरिक आयामों को मापने के लिए D) To mark lines | लाइनों को चिह्नित करने के लिए 46 / 4646. Q. What is the wear of metal pipe surface caused by impact of particles suspended in liquid? | तरल में निलंबित कणों के प्रभाव के कारण धातु पाइप की सतह क्या होती है? A) Scaling | स्केलिंग B) Rusting | रस्टिंग C) Erosion | कटाव D) Lamination | परतबंदी Your score is Facebook Restart